Welcome to Yacht Works      

Now In Four Locations!

2008  LAUNCH AND COMMISSION FORMS NOW AVAILABLE..................CLICK HERE!
Home Page Site Map Directions Weather Contact Us Search Tour Our Yard Feedback

 

Home Page
Back Up

Marina Construction 2000, Page 3

Backfilling the first two sections of seawall, click for larger photo. Lighthouse dredging out the launch wells, click for larger photo.

(left) Here a backhoe is backfilling the seawall with rock previously taken out of the site.

(right) In this photo, Lighthouse Construction is dredging out the blasted rock from the launching wells, and passing it back to a pile on land.  In the background Fitzgerald Construction is taking shot rock from the pile and backfilling the sea wall.  Note the "road" that Lighthouse built for the backhoe to work from.  It's twelve feet deep just off the end of that "road."  To dredge out to the harbor entrance, they had built this road most of the way out to the corner of the dock.  Most of it was just under the water.

Dredging continues, what looks like rocks in the water is ice chunks, click for larger photo. Third section of seawall being lowered into place, click for larger photo.

(left) Another "action" photo of the dredging.  In the right background can be seen the next section of seawall being prefabricated. 

(right) Lowering the next, third section of seawall into place.

Finetuning the location of the third section of seawall, click for larger photo. Curt Rice of Lighthouse Construction making his escape from dredging the harbor and launch wells, click for larger photo.

(left) Completing the lowering of the seawall section, the backhoe and a man on the North section guide the new piece into place.

(right) In the final stages of dredging, Lighthouse Construction works their way out of a corner of the launch wells.

New 75 ton launch well - sheeting going in place, click for larger photo. Placing outer crib between 25 T and 75 T launch wells, click for larger photo.

(left) After the third section of straight seawall, the complex corners and turns of the launch wells were installed.  These assemblies not only need to be straight, but to mate with the existing sheeting on both sides.  This is the 75 ton launch well, which is located right where Building 2 used to be.

(right) First of the launch well outer cribs is lowered into place.   Like the seawall these will be pinned to the bottom, and filled with concrete and rocks.

Aligning the outer crib on the bottom, click for larger photo. Outer crib for the 75 T launch well in place, click for larger photo.

(left) As the crib is lowered into place the crane and backhoe coordinate to make sure that it's in exactly the right place.  Note the "guy on ice," he's working.  The Fitzgerald crew used chainsaws to cut out the ice for the crib to go through.  Just like in the GOOD OLD DAYS, when ice was cut, and stored under sawdust in ice houses for summer refrigeration.  - And you though an ice house was just what people from Minnesota called fish shanties.-  In the background is the reincarnation of BUILDING 3 (.1)

(right) Both outer cribs in place.  Later they will be trimmed to the proper height, and a "bridge" running across from shore will carry the Travelift out to the end. 

Launch wells will all major parts in place, click for larger photo.

(left) Looking at the new launch wells from across the harbor.   Didn't think it was this easy to build a marina, did you??

this web site is always under construction

Back Up ]

Click to send a message to our webmaster.To e-mail our staff with questions about the content of this page click here.  Send email with questions or comments about the web site to Yacht Works' webmaster
Copyright © 2005 Yacht Works, Inc.              Yacht Works, Inc. Sister Bay, WI 54234 
Last modified: March 01, 2008                          (920) 854-2124       Fax (920) 854-2174

Thank you for being visitor # Hit Counter